Our 33 Litre Front Loading Benchtop Autoclave, available in Classic and Autofill versions, is ideal for laboratory research and is low in water. Have a question about Autoclaves, Sterilizers or Steam Generators? Our FAQ page has the answers. All the machines are supplied with a user manual but sometimes it is not consulted! Astell offer training to operators, and this is a service I recommend to ensure.

Author: Kigakus Vitaxe
Country: Czech Republic
Language: English (Spanish)
Genre: Software
Published (Last): 9 March 2012
Pages: 281
PDF File Size: 4.31 Mb
ePub File Size: 17.98 Mb
ISBN: 428-7-28801-418-3
Downloads: 33554
Price: Free* [*Free Regsitration Required]
Uploader: Monris

The Astell 120 – 344 Litre Front Loading Autoclave Range

The two controllers share most operating features and operations. To ashell from this: This allows the chamber to be cleaned out. At a pre-selected pressure during the cooling phase of the cycle, any remaining water in the chamber is evacuated to the drain. Our service staff are able to repair or maintain your equipment on site if required.

The Holdwarm temperature is automatically set to 25C below the Programmable Cooling-lock temperature set in the program.

Litre Front Loading Autoclave | Astell UK

PolyDev, based in Dunleer, Ireland, is a leading manufacturer of low volume, high value toric cosmetic contact lens, bringing together art and Temperature sensor is mounted clamped to the outside of the chamber. If an autoclave has a aetell generator little or no water remains in the end of the cycle.

In addition to laboratory use, it is not uncommon for benchtop autoclaves to be employed in other areas. Actual cycles that are required for particular loads may well differ from the ones shown here.

  ANSI HI 9.6.4 PDF

The ENGINEER will normally need to have been trained in a relevant disciplinepossibly as a Sterilizing Engineerbe conversant with Micro-Electronic system handling procedures, and be suitably qualified to carry out the adjustments and changes that may be required. The Programs may be Selected then Viewed in this way before a Program is started. These 4 switches control functions that cannot be set by the software or Configuration. If the Printer is fitted then the Printout Heading and cycle description will be printed.

It is accessed via the Supervisor Mode described earlier. The autoclace line shows the Current Sterilize Temperatureand Sterilize time. Press it again and Recorder power will turn off, and so on. The Astell – Litre Front Loading Autoclave Range The – litre front loading autoclave offers five chamber sizes, increased in capacity from the top loading range.

This system is integral with and dependent upon the use of the Load Sensing system. Water Solenoid Valve Feeds water to chamber. A e f g h i Page 39 Hold the roll so the paper feeds off the roll at manaul bottomtowards you.

The Process temperature is monitored during this stage.

Astell MXN451 5000 – 6000 Series Autoclave programming instructions

Yes, this is possible with most models. Select and Start the chosen Program. Astell is closing its offices and factory over the December festive period. Freesteaming may not be required for simple loads where the steam can penetrate the load easily. It is enabled in the User Configuration section. This can then be independently heated by the steam supply to allow drying to take place at the end of a cycle, or can be flooded with water during cooling to aid cooling times.


Autoclave service and maintenance – advice from the experts | News | Astell UK

Therefore when an autoclave is fitted with air ballast the cooling stage can be implemented earlier; this will mean that improved cooling times can be achieved. The Classic and Autofill Compact and Benchtop autoclaves can be used for small quantities of non-hazardous discard. This item not yet used. Manuxl chamber will cool down more quickly than the load, so if the Programmable cooling lock manuzl set to 99C the limiting factor will be the Preset Cooling Lock, This must be left set to suit the worst-case Liquid load if the autoclave is used for liquids.

Check the cause of the problem, or consult the Astell Service Dept. It also offers the ability to save cycle logs to a server or over FTP for backup. Is the Holdwarm facility available for models with steam generator?